EUCO 700: Semi-Rigid Joint Filler


• Semi-rigid formula that allows for limited temperature and humidity movement of concrete
• Tough performance reduces floor joint repairs and maintenance
• Suitable for filling cracks in older floors to reduce the rate of deterioration
• Available in selected color formulations for use with colored dry shake floor hardeners
• 33 colors available using color packs

Technical Data Sheet

Safety Data Sheet

Euco 700 Sealant Calculator

SKU: EUCO7002G Category: Tags: , , , , ,

EUCO 700: Semi-Rigid Joint Filler

EUCO 700 is a two-component, 100% solids semi-rigid epoxy for filling control and construction joints in industrial concrete floors. This product supports the joint edges and reduces spalling of the edges caused by wheel traffic. EUCO 700 has been designed for use in compliance with ACI 302 recommendations for epoxy joint fillers used in control and construction joints. EUCO 700 is available in Standard Gray and a Neutral Base, that can be colored with EUCLID UNIVERSAL COLOR PACKS; available in 33 standard colors. Questions? Contact Us.

• Concrete construction & control joints
• Crack filling in concrete floors
• Industrial and commercial floors
• Interior applications

Surface Preparation: The joint must be clean and sound. All oil, dirt, debris, paint and any other material that may be a bond breaker must be removed. All joint facings must possess an open surface texture with all curing compounds and sealers removed. If this product will be used for filling floor cracks, the cracks should be routed out and cleaned before filling. Ideally, all crack edges should be squared. The final step in cleaning should be the complete removal of all residue with a vacuum cleaner or pressure washing.

Joint Backing: Avoid the use of backer rod, sand or other fill material for the purpose of reducing volume. The full depth of the joint or crack must be filled with EUCO 700 for proper load transfer.

Priming: EUCO 700 does not require a primer before application.

Mixing: EUCO 700 is a two-part product and requires mixing. Premix each part separately before combining the materials. Pour all of the Part B hardener into the Part A resin and mix with a mechanical mixer and prop for 2 to 3 minutes. Make sure that the sides of the can are scraped to assure that all of the resin and hardener are thoroughly mixed.

Finish your job with Euclid Epoxies:

Euclid Eucothane 3 gallon

Euco Quick Joint UVR

Duralflex Fastpatch Epoxy Repair Mortar

Euclid Universal Color Packs: EUCO 700 can be colored using 1 EUCLID UNIVERSAL COLOR PACK (EUCO Pack) per 2 gal (7.6 L) unit and 2 EUCLID UNIVERSAL COLOR PACKS (EUCO Pack) per 10 gal (37.85 L) unit. Prior to mixing the unit together, stir the appropriate amount of colors packs into the part “A” side of the product until it is fully dispersed. Proceed with mixing as stated above. EUCLID UNIVERSAL COLOR PACKS are available in 33 standard colors, see EUCLID UNIVERSAL COLOR CHART for available colors.

Placement: After the liquids are thoroughly mixed, pour or gun the mixed material into the joint, filling it approximately 2/3 its full depth. Allow the joint filler to settle and then complete filling within 1 hour to the level of the floor. Use all material rapidly due to the short pot life.

Finishing/Shaving: Joints should be overfilled during placement. Cut flush with a razor knife or grind flush with the floor within 24 hours after placement. If EUCO 700 has completely hardened, heat may be used to soften the material for easier removal.

Curing: EUCO 700 will cure within 24 hours of placement @70°F (21°C). Lower temperatures will slow the curing rate.

Euclid Chemical

Weight 80 lbs
Dimensions 15 × 15 × 18 in

Neutral (2 Gallon), Standard Gray (2 Gallon), Neutral (5 Gallon), Standard Gray (5 Gallon)