CIM 1000 Premix: Trowel Grade
$828.50
- CIM 1000 Trowel Grade is a tough liquid applied urethane coating
- Chemically thickened to allow vertical application with minimum sag up to ¼ inch.
- ANSI/NSF 61 certified for potable water contact up to 82ºC.
- Cures in hours to form a tough elastomeric coating.
- Available in 4.5 gallons, 0.8-gallon kits, and cartridges.
161 in stock
Checkout stays fast. After purchase, set up a Metro reorder account to keep your order history together and make repeat orders easier.
CIM 1000 Premix: Trowel Grade
CIM 1000 Premix Trowel Grade is a tough, liquid applied, two component, chemical and corrosion resistant urethane elastomeric coating, chemically thickened to allow trowel applications with minimum sag. CIM 1000 Trowel Grade is designed for use with all CIM materials. CIM 1000 Trowel Grade can be used as a crack filler or for application to vertical surfaces and corner flashings. CIM 1000 Trowel Grade offers the same advantages as CIM 1000 and is approved for contact with potable water in accordance with ANSI/NSF 61. CIM 1000 Trowel Grade may be applied at thicknesses up to 250 mils on vertical surfaces in one coat. Questions? Contact Us
Features & Benefits
| Bonds to most substrates | Excellent adhesion provides a fully bonded waterproofing system |
| Lowest permeability in industry | Designed for constant immersion environments |
| High solids/low VOC | Compliant to toughest VOC regulations |
| UV stable | Suitable for applications in direct contact with UV |
| Excellent chemical resistant | Resistant to strong acids and bases |
| Excellent Concrete Crack Bridging | Bridge new cracks up to ¼ inch |
| Approved to ANSI/NSF 61 Standard | Suitable for contact with potable water for tanks as small as 5,000 gallons |
| Chemically thickened to provide high viscosity | Ability to build up to ¼ inch thickness in one application. |
Substrates must be clean and dry with no oils, grease or loose debris. CIM Bonding Agent is recommended on all non-porous substrates. Perform adhesion tests to confirm adequacy of surface preparation. See C.I.M. Industries’ specific substrate Instruction Guide for specific guidelines.
ICRI-CSP 4-6 surface profile exposing aggregate. Concrete must exhibit minimum 3,000 psi compressive strength and be free of release agents and curing compounds. The substrate must be clean and dry (see CIM Instruction Guide IG-2), and free of contaminates. Minimum 3 mil profile.
Immersion service – SSPC-SP10 / NACE No. 2 Near White Blast.
Non-Immersion service – SSPC-SP6 / NACE No. 3 Commercial Blast.
Use CIM Bonding Agent for greater adhesion.
SSPC-SP1 solvent clean and abrasive blast to roughen and degloss the surface. Use CIM Bonding Agent for greater adhesion.
Thoroughly clean. CIM Bonding Agent must be used for increased adhesion. For immersion service roughen the surface.
Substrate must be clean, dry and free of surface contamination.
CIM 1000 Trowel Grade may be applied over some existing coatings and linings and achieve acceptable performance. CIM Bonding Agent is recommended for greater adhesion. Finished system results vary due to a variety of project specific factors, including the service conditions to which the system is exposed. Therefore, C.I.M. Industries does not accept responsibility for determining the suitability of an existing coating and lining as a substrate for CIM products. Owner shall perform adhesion tests on any existing coating or lining to determine suitability.
Use CIM Scrim. Must be plural component spray applied.
CIM 1000 Trowel Grade is initially shiny black, turning dull over 3 to 6 months when
exposed to direct sunlight. For a colored or reflecting surface finish, see C.I.M Industries’ Instruction Guide, “Topcoats” (IG–7) for further instructions.
89%
88 g/l (0.74 lb./gal.). CIM 1000 Trowel Grade complies with the toughest VOC regulations. ©CIM 07/10
| Weight | 50.2 lbs |
|---|---|
| Dimensions | 12 × 12 × 18 in |
Related products
All Products
All Products
All Products
All Products
All Products
All Products
All Products